clamping

英 [ˈklæmpɪŋ]

美 [ˈklæmpɪŋ]

v.  (用夹具)夹紧，夹住，固定; 紧紧抓住; 紧夹住; 被抓住; 被夹紧; 用夹锁锁住(车)
clamp的现在分词

现在分词：clamping　

计算机

BNC.43220 / COCA.42307

柯林斯词典

• 夹子;夹具;夹钳
  Aclampis a device that holds two things firmly together.
• VERB (用夹具)夹紧，夹住，固定
  When youclampone thingtoanother, you fasten the two things together with a clamp.
  1. Somebody forgot to bring along the U-bolts to clamp the microphones to the pole.
     有人忘了带把麦克风固定在支架上的U形螺栓。
• VERB 将…固定(在某处)；紧紧抓住
  Toclampsomething in a particular place means to put it or hold it there firmly and tightly.
  1. Simon finished dialing and clamped the phone to his ear...
     西蒙拨完号，把听筒贴在耳边。
  2. He clamped his lips together...
     他紧闭双唇。
  3. You beg him to try just one spoonful, and he clamps his mouth shut...
     你求他就尝一匙，可他就是不张嘴。
  4. Peter jumped to his feet with his hand clamped to his neck.
     彼得一只手捂着脖子，腾地跳了起来。
• (将违章停放的车辆扣在原地的)夹钳，车轮固定夹
  Aclampis a large metal device which is fitted to the wheel of an illegally parked car or other vehicle in order to prevent it from being driven away. The driver has to pay to have the clamp removed.

in AM, use 美国英语用 Denver boot


• VERB 给(车辆)上夹钳
  Toclampa car means to fit a clamp to one of its wheels so that it cannot be driven away.
  1. Courts in Scotland have ruled it illegal to clamp a car parked on private ground and then to demand a fine.
     苏格兰法院裁定，将停在私人地界上的车辆上夹钳并索要罚款的行为是违法的。

in AM, use 美国英语用 boot

双语例句

• The clamping force control and the ratio control is the most important parts of the CVT control technology.
  夹紧力控制与速比控制是CVT控制问题中最为重要的两个方面。
• The clamping schemes of thin-walled package were discussed on the base of FEM analysis.
  采用有限元分析方法，对薄壁件的装夹方案进行了讨论。
• The turret has Curvic coupling for high positioning accuracy and the hydraulic clamping for heavy cutting.
  该刀塔具有Curvic耦合高定位精度和液压夹紧为重切削。
• Mechanical shaft clamping via single taper mechanism, hydraulically actuated, including tailstock support.
  通过液压系统操纵锥体，连同尾架支承将工件机械夹紧。
• Sealed bearing system reduces clamping pressure and increases bearing life.
  密封的轴承系统减少夹持力并增加轴承寿命。
• Analysis of Positioning and Clamping for Workpiece in Machining Center
  工件在加工中心上的定位与夹紧分析
• The utility model provides a reliable clamping device for connection between various nonmetallic hoses and hard tubes.
  在为各种非金属软管与硬管的联接上，提供了可靠的卡具。
• Relay IC3 opens, protecting the amplifier and clamping diodes.
  继电器IC3断开，保护放大器和钳位二极管。
• Hydraulic hob mandrel clamping.
  液压滚心轴夹紧。
• Thirdly, how to obtain the alterable clamping force was studied.
  研究了求解变夹紧力的优化方法。